收藏本站
NCP1027
5.0 V/3.0 A Universal Mains Power Supply
Due to its low R DS(on) , the NCP1027 can be used in
universal mains SMPS up to 15 W of continuous power,
provided that the chip power dissipation is well under
control. That is to say that average power calculations and
measurements have been carried and correlated. The
design of an SMPS around a monolithic device does not
differ from that of a standard circuit using a controller and
a MOSFET. However, one needs to be aware of certain
characteristics specific of monolithic devices. Let us
follow the steps:
V in min = 120 Vdc
V in max = 375 Vdc
V out = 5.0 V
V out = 15 W
Operating mode is CCM
h = 0.8
1. The lateral MOSFET body- diode shall never be
forward biased, either during startup (because of a
large leakage inductance) or in normal operation
as shown by Figure 45. This condition sets the
maximum voltage that can be reflected during t off .
350
250
150
50.0
> 0 !!
-
50.0
1.004M
1.011M
1.018M
1.025M
1.032M
+ 110 + 18.3 or
Vin
5 ) 1
Vout ) Vf
d max +
+
+ 0.49
NVout ) Vin, min
(eq. 16)
1 ) NV
Figure 45. The reflected voltage shall always be greater
than the minimum input voltage to avoid the forward
biasing of the MOSFET body-diode.
As a result, the Flyback voltage which is reflected on the
drain at the switch opening cannot be larger than the input
voltage. When selecting components, you thus must adopt
a turn ratio which adheres to the following equation:
N(Vout ) Vf) t Vin, min t Vin min (eq. 14) . In our case,
since we operate from a 120 V DC rail while delivering
5.0 V, we can select a reflected voltage of 110 V
DC maximum: 120-110 > 0. Therefore, the turn ratio
Np:Ns must be smaller than
Np : Ns t 19 . We will see later on how it affects the
calculation.
2. Lateral MOSFETs have a poorly doped
body-diode which naturally limits their ability to
sustain the avalanche. A traditional RCD
clamping network shall thus be installed to
protect the MOSFET. In some low power
Figure 46. Primary Inductance Current
Evolution in CCM
turn ratio, V out the output voltage, V f the
secondary diode forward drop and finally, I peak
the maximum peak current. Worse case occurs
when the SMPS is very close to regulation, e.g.
the V out target is almost reached and I peak is still
pushed to the maximum. For this design, we have
selected our maximum voltage around 650 V (at
V in = 375 Vdc). This voltage is given by the RCD
clamp installed from the drain to the bulk
voltage. We will see how to calculate it later on.
3. Calculate the maximum operating duty-cycle for
this flyback converter operated in CCM:
NVout 1
Vin,min
out
4. To obtain the primary inductance, we have the
choice between two equations:
) Ipeak
(eq. 15) , where L f is the leakage
L + , where K +
and
applications, a simple capacitor can also be used
since Vdrain max + Vin ) N (Vout ) Vf)
Lf
Ctot
inductance, C tot the total capacitance at the drain
node (which is increased by the capacitor you
will wire between drain and source), N the Np:Ns
?
(Vind)2 D IL
(eq. 17)
fSWKPin I1
defines the amount of ripple we want in CCM
(see Figure 46).
Small K: deep CCM, implying a large primary
inductance, a low bandwidth and a large leakage
inductance.
http://onsemi.com
25
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
NCP1608BOOSTGEVB BOARD EVAL NCP1608 100W BOOST
NCP1631PFCGEVB BOARD DEMO NCP1631 INTERLEAV PFC
NCP1650EVB BOARD EVAL NCP1650 PFC CTLR
NCP1652L48VGEVB BOARD EVAL 100W 48V NCP1652 PFC
NCP1653EVB BOARD EVAL FOR NCP1653
NCP2993FCT2GEVB BOARD EVAL NCP2993 AUDIO PWR AMP
NCP345SNT1G IC DETECTOR OVER VOLTAGE 5TSOP
NCP346SN2T1G IC DETECTOR OVER VOLTAGE 5TSOP
相关代理商/技术参数
NCP1606ADR2G 功能描述:功率因数校正 IC PWR FCTR CONTROLLER RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel
NCP1606APG 功能描述:功率因数校正 IC LO CST PWR FCTR CONT RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel
NCP1606BDR2G 功能描述:功率因数校正 IC PWR FCTR CONTROLLER RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel
NCP1606BOOSTGEVB 功能描述:电源管理IC开发工具 OSPI NCP1606 100 W BOOST RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
NCP1606BPG 功能描述:功率因数校正 IC LO CST PWR FCTR CONT RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel
NCP1607BDR2G 功能描述:功率因数校正 IC CST EFCT PW FCTR CTR RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel
NCP1607BOOSTGEVB 功能描述:BOARD EVAL NCP1607 100W BOOST RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:* 标准包装:1 系列:PCI Express® (PCIe) 主要目的:接口，收发器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要属性:- 次要属性:- 已供物品:板
NCP1608BDR2G 功能描述:功率因数校正 IC COST EFFECT PWR FACT CONT RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel